How to Remove a Chuck from a Drill Press

Advertiser Disclosure: Tool Inspector earns commissions from qualifying purchases.

Are you wondering how to remove a chuck from a drill press? Here are the steps that you can take to do it.

 

Supplies and Tools Needed to Remove a Chuck from a Drill Press

Here are the supplies and tools that will be needed.

  • Compressed air can or air compressor
  • Eye protection
  • Drying lubricant
  • Clean cloth
  • Allen wrenches
  • Replacement chuck (if required)
  • Open-end Wrenches (if required)
  • Mallet (if required)

 

How to Remove a Chuck from a Drill Press in 5 Steps

Once you have the correct tools and accessories, follow these instructions to remove the chuck from your drill press.

 

Chuck Cleaning

Before you start cleaning up the chuck, make sure that the power cable is disconnected from the electrical outlet. This is paramount for safety.

 

The bits in the chuck should be removed and then the collar rotated. This will extend the jaws. Using a lint-free dry cloth, have the chuck wiped clean.

 

Now the jaw should be completely retracted. With the help of compressed air, blow away present in the jaw opening. The compressed air will be most useful in clearing the chuck jaws from any dirt or loose sawdust that may be present.

 

Important Safety Tip: when you are using compressed air to blow away dust and debris make sure that you are wearing safety glasses so that particles don’t get in your eyes and damage them.

 

Chuck Lubrication

After you have cleaned up the chuck, you should lubricate it with some drying lubricant. Try spraying Boeshield T-9 for it a drying lubricant that works well.

 

The chuck’s open jaws should be sprayed with this lubricant. Turn the collar around and retract then extend the jaws a few times so that lubricant works its way into the structure. Wipe out any excess lubricant that you can find.

 

In most cases, this easy method of lubricating and cleaning will return your chuck to its original working condition. But if that doesn’t work out, you can remove the chuck for a more meticulous approach.

 

Take Out the Chuck

For the majority of hand-held drills, you can remove the chuck simply by working the screw loose. You can find this screw in the chuck’s open jaws.

 

But things are different in a drill press. The chuck comprises a tapered shaft. This is made to pressure-fit inside the spindle.

 

You can start removing it in the following way. Depress the handle of the tool so that the quill is lowered. Keep doing this till the chuck and quill go as far as possible. Turn around the quill lock so that the structure is held in the lower position.

 

Now find the big vertical shaft that is inside the quill shaft. After this slot is found, put in the chuck removal key. Then strike the end of this using a mallet so that the chuck is knocked away from the spindle.

 

If there is no removal key for your chuck nor any slot for it, you can try the following. Elevate the quill so that the chuck collar’s top edge is located around half an inch under the drill casing. Now have the quill lock tightened so that the quill is secure. Taking a big open-end wrench, have its mouth slide along the quill spindle so that it is located above the collar of the chuck. Apply an upward force on this wrench so that the chuck may be pried out loose from the spindle of the quill.

 

Clean Up the Chuck

When you have removed the chuck, clean up the chuck’s tapered shaft by wiping it with a lint-free dry cloth. Using compressed air, clean up the opening towards the quill spindle’s lower part so that sawdust and grime are removed.

 

In case the chuck is damaged or badly worn out, you can try buying a new one. But after cleaning, if it looks to be in good shape, you can reinstall it.

 

Reinstall the Chuck

You will have to either reinstall or replace the chuck. You can do this by raising the quill to its topmost level. Have the quill lock tightened so that the spindle is secure? You should turn the table of the drill press so that it does not come in the way. This way, it will not obstruct chuck installation.

 

Your next step is to slide down the shank of the tapered chuck so that it goes towards the quill spindle. Turn the chuck a bit using your hand so that the head towards the upper shank easily fits inside the space located in the spindle. Fully retract the chuck jaws. Now strike the chuck bottom using the mallet so that the chuck shank is seated inside the quill spindle.

 

Spin the collar of the chuck to ensure that the chuck will work as intended. Have the motor plugged in. Put the drill bit inside the check and then try it out by running a few simple tests. Make a couple of bores to confirm that the chuck is working correctly.

 

Keeping a drill press close at hand can ensure that you can perform all drilling operations with ease. This is the advantage that woodworkers have over carpenters who need to haul their tools to their work site.

 

A good drill press like the one mentioned above is capable of creating big large holes safely and efficiently. Less exertion is required compared to using a hand-operated drill. The drill press is great for other tasks like boring larger diameter holes.

 

Our Final Thoughts

Courtesy of the simple guide outlined above, you now know how to remove a check from a drill press. Turns out it isn’t so hard after all.