How to Measure Band Saw Blades

Advertiser Disclosure: Tool Inspector earns commissions from qualifying purchases.

Band saws appeal to anyone who prefers working with wood, metal, or plastic. With your idea in mind, you’ll precisely slash your material to match your needs and requirements.

It’s impossible to compare two bands because each has its own set of teeth, length, width, and height. To begin, check to see if the blade size of your machine is appropriate for the job at hand.

When using a band saw, the procedure for estimating the length of the blade is quite intuitive. Is there a way in which you can easily know the length of band saw blades? Do you know how to use it? This article discusses how to measure band saw bladesĀ in depth.

How to Measure Band Saw Blades: 3 Methods

Band saws are a piece of machinery used to cut through the material. Its long and powerful blade is used in place of the standard blade. There is a wide range of sizes and shapes to choose from.

The teeth’s strength can be used to cut through various materials. It should be obvious that the engines of all band saws are powered by motors. It is possible to find out how long a band saw blade is in the following ways:

Method No. 1

If you don’t have access to a band saw blade, you can use this method:

  • Stabilize the pulleys or wheels of the band saw.
  • Measure the distance between the center hubs of both the driven and undriven band wheels. This center will be referred to as C during calculations.
  • Now, you’ll measure each wheel’s circumference from the center to the outermost edge to get its inch radius.
  • Perform the calculation using the given formula – (R1 x 3.1416) + (2 x C). Remember that the blade’s length is equal to the saw’s length

Method No. 2

If you have a band saw blade that simply has worn or missing teeth and want to repair it, you need to follow the following steps:

  • Tape off the starting spot with a piece of masking tape.
  • This is where you will draw a line on the inside of the blade hoop and the tape to show where it is located.
  • At some point after one revolution, you’ll notice a line running along your blade’s inside edge.
  • Stabilize the blade and make a final mark on another piece of tape where the initial mark was created in the previous step.
  • In this step, determine the distance between the two markers.

Method No. 3

If you have a band saw blade that appears to have lost its length and want to repair it, you should opt for the following method:

  • Check to see that the sheared ends fit together like a puzzle.
  • Because some of the blade was sheared off, it’s impossible to know exactly how old it really is. If the two ends don’t fit together precisely, the band saw blades might be outdated.
  • Lay it horizontally to help straighten the blade.
  • Measure the entire length of the blade.

Ideal Length of Blades

Most band saws accept blades with lengths ranging from 2 inches on the short end to 8 inches on the long end. If a blade is missing or a replacement blade is needed that may or may not fit the band saw machine, the length range of the band saw machine must be determined.

Turn the knob counter-clockwise until it stops moving to lower the upper wheel. Remember that it’s necessary to gauge the distance between the centers of the upper and lower wheel shafts.

How to Determine the Width and Depth of a Band Saw Blade

Now that you know how to measure the length of a band saw blade, let’s move on to the width and depth measurements. To get precise measurements, all you’ll need is a ruler, chalk, and a marker pen.

  • Measure from the saw’s edge to the teeth to measure the band saw’s width.
  • You can use a ruler or tape measure to acquire an exact measurement.
  • You can measure the width of your band saw’s blade with a tape measure.
  • When you get to the other end, slowly pull the tape measure across the band saw’s blade.

Measurement Requirements for Two-Wheel Band Saws

  • Adjust the wheels to ensure they are not too far out of alignment. They should be intact in the middle of the adjustment range.
  • Tighten the band.
  • If necessary, re-weld the blade. Opt for a setting in the middle for optimal results.
  • It is 3.1416 for R1, 3.1416 for R2, and 3.1416 for R3 (2 x D)
  • Know the distance between the wheels
  • Determine the rim diameter

Measurement Requirements for the Upper Wheel

It is necessary to measure the distance between the upper and lower streaks. Do so by following the instructions given below:

  • Make sure you multiply the decreased distance between shafts by two because it’s twice as long as before.
  • You should add a full wheel circumference to account for the blade traveling partially around the upper and lower wheels.
  • Inscribe the tip of the blade with some sort of mark.
  • Set a measuring tape to 0 inches and make sure it’s straight.
  • Afterward, spin the blade in an anti-clockwise direction.
  • The result is the length of the saw’s shortest blade.

The same techniques are used to determine the longest blade length. Check your vehicle’s owner’s manual to see how long each one lasts. Measuring length is a lot easier with an old saw blade that fits your band saw.

Final Words

And you are done! That’s how to measure band saw blades. Make sure to be very precise with your measurements. Follow the instructions to the dot to achieve accurate results. Even though it is a relatively easy task to measure the length and width of a band saw, you must take caution.

You need to have the perfect band saw; otherwise, concluding the task of woodcutting will be challenging for you.